+86-182-9191-0663 丨  sales@hiltechgroup.com | support@hiltechgroup.com

About Us

Since 1998 丨 HILTECH®

You are here: Home » Products » Flow Measuring Instrument » Electromagnetic Flow Meter » Insertion Magnetic Flow Meter

Insertion Magnetic Flow Meter

Share to:
  • Applicable sizes: 2"~120" (50~3000 mm) 
  • Operating pressure: ≤ 1.6MPa 
  • Velocity range of 0.5~10m/s 
  • Accuracy: ±1.5%  
  • Conductivity of measured medium: ≤ 20 μs/cm 
  • Electrode materials: 316L, Hastalloy, Ti, Ni, Tantalum
Availability:
Quantity:


Insertion Magnetic Flow Meter introduction

Insertion Magnetic Flow Meter, also called insertion electromagnetic flow meter, is an insertion type flow meter. Insertion magnetic flowmeter can be installed without stopping the flow. Suitable for large diameter DN300-3000.

Insertion Magnetic Flow Meter adopts pressure tapping and installation technology. Insertion electromagnetic flow meter is composed of insertion electromagnetic sensor and electromagnetic flow converter.

Installation can be divided into an online installation type of the cut-off valve, and water control installation type without stop valves. The Insertion Magnetic Flow Meter is suitable for measuring the volume flow of various conductive liquids in the pipeline. It can also be used to measure corrosive conductive liquids such as acid, alkali and salt.


Insertion Magnetic Flow Meter Features


Compared with the pipe segment electromagnetic flowmeter, the advantages of Insertion Magnetic Flow Meter:

  • No need to cut off the water, cut off the pipeline, install directly on the old pipeline;

  • Easy to disassemble during maintenance;

  • Especially suitable for large-diameter pipelines, with high cost performance;

  • The accuracy is lower than the flange type, and it is mostly used for process control rather than measurement;

  • It can be made into one-piece or component pose;

  • The Insertion electromagnetic structure can be easily installed and disassembled without stopping the water under low pressure or under pressure. Therefore, it is very suitable for the fluid measurement of existing pipelines and facilitates the maintenance and repair of instruments.

  • The measurement accuracy is not affected by changes in physical parameters such as the temperature, pressure, density, viscosity, conductivity (as long as the conductivity is greater than 20μs/cm) of the measured medium.

  • The sensor has almost no pressure loss and extremely low energy loss.

  • Large flow measurement range. The full-scale flow rate in the measured pipe can be set arbitrarily from 1m/s to 10m/s, and the output signal has a linear relationship with the flow rate.

  • The flowmeter not only has 0~10mA or 4~20mA standard current output, but also 1~5kHz frequency output


Insertion Magnetic Flow Meters specification



Media Conductivity:> 20 μS/cm
Sizes:2″~120″ (50-3000mm)
Measuring Range:0.5 – 10 m/s – bi-directional
Temperature:up to 248°F (120°C) max.
Pressure:up to 230 psig (1.6Mpa) max.
Materials of Construction:Transmitter Housing: Aluminum Probe: SS #304 (std), 316L, Ti Electrode: 316L, HC-22, HB3, Ti
Accuracy:±1.5% of reading (velocity v≥1m/s)
Display:Flow rate, flow velocity, percentage, Total flow
Grounding Resistance:Must be ≤ 10 Ω
Protection:IP 65 or IP 68 (Submersible, with remote style)
Connection:Weld, ball valve(threaded and flanged)
Ambient temperature:-13 to 140°F (-25 to 60°C)
Cable entry:2 X PG11
Outputs:4-20mA, Pulse
Communication:RS232/485/HART, Modbus
Power requirements :19-36 VDC, 12-15W, 85-265 VAC, 45-63 Hz, ≤20W




-Manuals

Insertion Magnetic Flow Meters

-Data sheet


Insertion Magnetic Flow Meter Application

  • Potable Water

  • Water Distribution

  • Pumping Stations

  • Filter Balancing and Backwash

  • Reclaim Water

  • Treated Water

  • Irrigation Water

  • Cooling Water

  • Raw Water

Applications-of-Insertion-Magnetic-Flow-Meter1Applications-of-Insertion-Magnetic-Flow-Meter2Applications-of-Insertion-Magnetic-Flow-Meter3Applications-of-Insertion-Magnetic-Flow-Meter4

Previous: 
Next: