As a portable terminal, the Model BT200 BRAIN TERMI-NAL is used in combination with equipment using brain communication for setting, changing, displaying and printing out parameters such as tag number, output mode,and range, through simultaneous communication. It also monitors I/O values and self-check results, sets constant- current output , and allows zero adjustments.
The Model BT200 BRAIN TERMINAL is used by connecting it between 4 to 20 mA DC signal transmission lines of the equipment or to a dedicated connector on the ESC (Signal Conditioner Communication Card) when the system is started up or maintained.
1.Online monitoring and communication
The modulated communication signal does not interrupt the 4 to 20 mA DC signals during communication.
2. Common to all Yokogawa’s equipment
The Model BT200 BRAIN TERMINAL works with allequipment that uses BRAIN communication.
3. Easy of use
A large display (21 characters by 8 lines) eases setup andalteration procedures in English prompting interactive
sequences.
4. Diagnostics/security with error messages
• Self-check function
• Security code protection of setpoints
• Low battery voltage alarm
• Automatic power-off
5. Printer (BT200-P00)
Printer prints out tag numbers and other parameters on the spot.
6. Intrinsic safety (Only for a without printer type)
CSA intrinsically safe approval.
As a portable terminal, the Model BT200 BRAIN TERMINAL is used in combination with equipment using brain communication for setting, changing, displaying and printing out parameters such as tag number, output mode, and range, through simultaneous communication. It also monitors I/O values and self-check results, sets constantcurrent output, and allows zero adjustments.
Feature |
|
EMC Conformity Standards | EN61326-1 Class A, Table2 (For use in industrial locations), EN61326-2-3 |
Display: | LCD dot matrix, 21 characters |
Power Supply: | Five AA 1.5 V dry alkali batteries (LR6/AM3 (N)) For Intrinsic safety type; Five designated batteries (see OPTIONS) |
Dimensions: | BT200-N00 . . . 228*110*51 mm (9.0*4.3*2.0 inch) BT200-P00 . . . 321*110*61 mm (12.6*4.3*2.4 inch) |
Approximate Weight: | BT200-N00 . . . 510 g (1.12 lb) BT200-P00 . . . 700 g (1.54 lb |
• - Online monitoring and communication The modulated communication signal does not interrupt the 4 to 20 mA DC signais during communication.
• - Common to ail Yokogawa’s equipment The Model BT200 BRAIN TERMINAL Works with ail equipment that uses BRAIN communication.
• - Easy of use A large display (21 characters by 8 lines) eases setup and alteration procedures in English prompting interactive sequences.
• - Diagnostics/security with error messages
• - Self-check function
• - Security code protection of setpoints
• - Low battery voltage alarm
• - Automatic power-off
-Manuals
Device Smart Communicator BT200
-Data sheet
Printer (BT200-P00) Printer prints out tag numbers and other parameters on the spot. Equipment Spécifications Applicable Equipment:
[Field Instruments]
DPharp
ADMAG
YEWFLO
YTA [Signal Conditioner]
Signal Conditioner for CENTUM Communication
Spécification: Yokogawa original protocol
Modulation: Burst modulation 0: 2400 Hz 1 :
Signal without carrier Baud rate: 1200bps
Communication signal: host to device: +/- 0.5 V (load résistance 250 Q) device to host: +/- 2 mA Communication Line: [Field Instruments] Load résistance: 250 to 600 Q (including cable résistance)
Load capacitance: 0.22 pF or less Load inductance: 3.3 mH or less Power line spacing: 15 cm (6 inch) or more (Avoid parallel wiring.)